Recent content by Fuqua588
-
F
Recommended Catch Can kit for Gen 3 5.7
I was wondering what catch can is the best for my 2008 5.7 hemi i cant find one that is marked for the 3rd gen hemis and ik certain ones arent worth it also what else should i look out for what kind of fitting will i need and what not. any recommendations would be appreciated.- Fuqua588
- Thread
- Replies: 0
- Forum: Engine & Performance
-
F
Replaced fog lights
yea i got it all hooked up this morning with some heat shrinks and now they work gonna see if its all cleanly connected tonight and make sure they dont flicker while driving... thank you everybody -
F
Replaced fog lights
This is my issue the wire that I stripped I hooked up and they turned on but it’s to short for me to tape up and trust so what gauge wire is this and can I just cut me a putt piece and throw in there with two butt connector heat shrinks and be worry free or is there any way I can replace the... -
F
Replaced fog lights
i thinkj i have found the issue i have a cut wire i have a few wires that are freyed into right under the fuse box but only one completly cut off im guessing that is the culprit i will post a pic here soon might need some help with wiring also looks like something started to get in there at some... -
F
Replaced fog lights
yea i did and i did see people say that about the leds and it being because the polarity is off but im not sure how to check the polarity of the leds and im not sure how the polarity could be wrong unless the part bought was wired backwards is their something else to this that i havent found... -
F
Replaced fog lights
yes and no i bought some aftermarket led lights cause i figured it was just the bulbs of the old ones that went bad but yes its all oem and is the module connected to the outside of the fusebox below it or is it under the initial panel of fuses inside the fusebox? i know their is a screw on top... -
F
Replaced fog lights
ive replaced the fog lights and they still dont work i bought the truck recently and the fog lights didnt work then and they still dont work now. i looked into it maybe being a fuse but on the 3rd gens they did the tipm and ive searched the internet and checked the owners manual and there is no... -
F
2008 5.7 hemi modest truck build?
How do I do that myself- Fuqua588
- Post #9
- Forum: Engine & Performance
-
F
2008 5.7 hemi modest truck build?
that’s what I figured after the mds delete kit with the stage 1 cam. I plan on getting some L.T.Hdrs with that kit but where do I look for a tune and also the trans Idk what to do with that. I can’t find much on 03-08 5.7 ram builds. Also if I cut out the cats how do I keep the o2 sensors from...- Fuqua588
- Post #7
- Forum: Engine & Performance
-
F
2008 5.7 hemi modest truck build?
Also will the 392 lifters and springs work on the pre vvt models I mean from I’ve seen the lifters do seem pretty much plug and play I’m just making sure I get it all right- Fuqua588
- Post #5
- Forum: Engine & Performance
-
F
2008 5.7 hemi modest truck build?
What long tube headers would you recommend? That are good for the price and aren’t to bad of a fit if that’s a problem with any of them.- Fuqua588
- Post #4
- Forum: Engine & Performance
-
F
2008 5.7 hemi modest truck build?
- Fuqua588
- Post #2
- Forum: Engine & Performance
-
F
2008 5.7 hemi modest truck build?
I just bought a 08 5.7 100100 miles on it I’m already looking to get the full ams mds delete kit with the Melling high volume oil pump and some jba shorty headers down the line and true dual it to some subtle throaty mufflers haven’t gotten that far yet but what else would help compliment all...- Fuqua588
- Thread
- Replies: 8
- Forum: Engine & Performance
