Recent content by Spsully
-
5.7 internals meet outside world
https://youtu.be/IGR3bjB1fHE?si=Vzf8cDm86UISXBHx That's today's update- Spsully
- Post #77
- Forum: Engine & Performance
-
5.7 internals meet outside world
And she's mobile. Still working on the tune and the interior. But I drove her a few times today for data logging.- Spsully
- Post #76
- Forum: Engine & Performance
-
5.7 internals meet outside world
Beads.... life is always good- Spsully
- Post #75
- Forum: Engine & Performance
-
Opt-y Tailgate Bar - did you need the tow package module?
No pictures yet..... but I installed Opt-7 redline and so far am very impressed with it. -
How To: Bedside Utility Racks
so all these years later, Im searching google and it gives me this link. Going to use this as motivation on mine for sure. I probably will do the peg board like you said you wouldnt do. but instead of putting nuts on the back, I just add rivnuts to each hole as I need to add stuff. Thank you...- Spsully
- Post #51
- Forum: 4th Gen DIY
-
2005 Ram 1500 5.7l hemi swap
Also.... as someone that just went through putting an 05 motor in my 04 truck with 06 coils. I have very recent and personal knowledge of the EXTREMELY minor differences. Like the 04 and 05 pcm even with matching part numbers has different connectors. I had to rebuild my harness like 3 or...- Spsully
- Post #17
- Forum: Engine & Performance
-
2005 Ram 1500 5.7l hemi swap
Location? I have heads 34450 is the zip- Spsully
- Post #16
- Forum: Engine & Performance
-
5.7 internals meet outside world
Been gone for so long you all probably forgot about me. Not sure where to even start. Motor went in. Ground issues wouldn't let it even try to Crank. Fixed that More ground issues wouldn't let it start.... seriously? Fixed that Injectors/ coils wouldn't fire correctly. Acted 180...- Spsully
- Post #73
- Forum: Engine & Performance
-
5.7 internals meet outside world
Got the motor fully bolted in and mated to the tranny. Installed the ps pump, then decided that the pulleys didn't match so I pulled it off and painted it. Yes I fixed the twisted up ps line. New ac compressor and alt got painted and installed. (No picture yet) wiper cowl got put back on...- Spsully
- Post #72
- Forum: Engine & Performance
-
5.7 internals meet outside world
Only 2 bolts in the bell housing but it is in its home- Spsully
- Post #71
- Forum: Engine & Performance
-
5.7 internals meet outside world
Took a couple quick pictures of the cleanliness of the engine bay before I started this morning. Still pretty excited about how little rust there is. This would never happen in New England.- Spsully
- Post #70
- Forum: Engine & Performance
-
5.7 internals meet outside world
Haven't updated in a while.... so here goes Dropped the factory exhaust and installed my 3" dual exhaust Wiring harness got finished, but i have to junk the main section because mine is different. So excited about that. Got my gauges in and wired up. I'm officially a poser. But GPS...- Spsully
- Post #69
- Forum: Engine & Performance
-
Wanting to swap 2012 Laramie Longhorn Console to Jumpseat
soooooo, I previously put the 4th gen jump seat in my 3rd gen. and now I am taking it out and dropping the center console in. I wont have the bottom part of your dash, but I do have the seat, seatbelt, and under seat console. -
-
5.7 internals meet outside world
I had the motor ready to go in and the train hasn't stopped in days. So im redoing some of the wiring harness.- Spsully
- Post #68
- Forum: Engine & Performance
