Recent content by SitKneelBend
-
OEM Hemi Exhaust on the V6
It does, but you don't need them. You will only be replacing exhaust from the muffler on back.- SitKneelBend
- Post #8
- Forum: V6 Engine & Performance
-
OEM Hemi Exhaust on the V6
Muffler and back. The parts you will need are the muffler, tail pipes (x2), and exhaust tips (x2). If you can, try to get the rubber exhaust hangers too from the muffler on back. He shouldn't have to cut anything...- SitKneelBend
- Post #5
- Forum: V6 Engine & Performance
-
Transmission filter and fluid change !!! (3.6 Pentastar Specific Please)!!!
I moved my conversation on it over to a thread with lots of participation to get advice myself. You can start reading here for my experience... https://www.ramforum.com/threads/transmission-pan-and-fluid-change-questions.190401/post-2908664- SitKneelBend
- Post #5
- Forum: 4th Gen DIY
-
Transmission pan and fluid change questions
I used MOPAR... Chrysler Genuine 68172556AA Oil Pan Gasket https://a.co/d/6sfSZ47- SitKneelBend
- Post #235
- Forum: General Discussions
-
OEM Hemi Exhaust on the V6
I've had mine on for nearly 10 years without issue. You can do it with or without a dual cutout bumper as the rear tips are adjustable. You can add the second exhaust hangar for the extra pipe as the mounting location should already be on your truck. Plug and play, did it by myself with the...- SitKneelBend
- Post #2
- Forum: V6 Engine & Performance
-
Light upgrade to my base system
Nice! What Amp did you end up using?- SitKneelBend
- Post #2
- Forum: Audio & Electronics
-
Transmission pan and fluid change questions
With the wheels able to spin freely, you can disable ESC (button near Tow/Haul button below the radio) and use the steering wheel gear selection buttons (+ and -) to limit the top gear to 2nd gear (must be in drive to select gear). Then just gas it up to about 2000RPMs and it should easily...- SitKneelBend
- Post #229
- Forum: General Discussions
-
Driver Seat
I believe the airbag just blows right through the stitching...- SitKneelBend
- Post #6
- Forum: Interior
-
Transmission pan and fluid change questions
It must be done while running and the transmission leveled AND having gone through the gears and getting to second gear. This fills the transmission circuits. Not doing this will result in fluid draining out that would otherwise be somewhere in the transmission system unable to drain into the...- SitKneelBend
- Post #227
- Forum: General Discussions
-
Sirius XM Phone App
You need to switch the the Bluetooth input to hear it.- SitKneelBend
- Post #5
- Forum: Audio & Electronics
-
Vp4 uconnect in a 2018 ram 2500
I'll pile on this and say that screen prices have fallen drastically and replacing the whole screen assembly is easier than just the digitizer.- SitKneelBend
- Post #3
- Forum: 4th Gen DIY
-
Transmission pan and fluid change questions
I'll add one more thing for you and others who do this that I haven't seen mentioned yet. When you are done, wipe the rear of the pan down real good and go on a test drive. After the drive, you might see what looks like leaks around some of the rear bolts but in my case it was just excess...- SitKneelBend
- Post #225
- Forum: General Discussions
-
Transmission pan and fluid change questions
Mine slid in pretty easy and firmly held in place. No issues whatsoever.- SitKneelBend
- Post #222
- Forum: General Discussions
-
Transmission pan and fluid change questions
That's good to hear! I kinda went into it thinking I'm not concerned with what comes out but only that I follow the fill procedure properly so I know it's good. I was going to get the 1qt pan but purchased the 2qt because it was slightly cheaper.- SitKneelBend
- Post #221
- Forum: General Discussions
-
Transmission pan and fluid change questions
To pile on, your PPE pan will have very clear printed instructions with the bolt pattern sequence.- SitKneelBend
- Post #219
- Forum: General Discussions
